|
| void | setup () override |
| |
| void | loop () override |
| |
| void | dump_config () override |
| |
| water_heater::WaterHeaterCallInternal | make_call () override |
| |
| void | set_communication_timeout (uint32_t value) |
| |
| void | set_primary_temperature_sensor (sensor::Sensor *value) |
| |
| void | set_secondary_temperature_sensor (sensor::Sensor *value) |
| |
| void | set_target_temperature_sensor (sensor::Sensor *value) |
| |
| void | set_estimated_heating_time_sensor (sensor::Sensor *value) |
| |
| void | set_available_water_sensor (sensor::Sensor *value) |
| |
| void | set_communication_sensor (binary_sensor::BinarySensor *value) |
| |
| void | set_power_sensor (binary_sensor::BinarySensor *value) |
| |
| void | set_heating_sensor (binary_sensor::BinarySensor *value) |
| |
| void | set_mode_sensor (text_sensor::TextSensor *value) |
| |
| virtual float | get_setup_priority () const |
| | priority of setup().
|
| |
| float | get_actual_setup_priority () const |
| |
| void | set_setup_priority (float priority) |
| |
| void | call () |
| |
| virtual void | on_shutdown () |
| |
| virtual void | on_safe_shutdown () |
| |
| virtual bool | teardown () |
| | Called during teardown to allow component to gracefully finish operations.
|
| |
| virtual void | on_powerdown () |
| | Called after teardown is complete to power down hardware.
|
| |
| uint8_t | get_component_state () const |
| |
| void | reset_to_construction_state () |
| | Reset this component back to the construction state to allow setup to run again.
|
| |
| bool | is_in_loop_state () const |
| | Check if this component has completed setup and is in the loop state.
|
| |
| bool | is_idle () const |
| | Check if this component is idle.
|
| |
| void | mark_failed () |
| | Mark this component as failed.
|
| |
| void | mark_failed (const LogString *message) |
| |
| void | disable_loop () |
| | Disable this component's loop.
|
| |
| void | enable_loop () |
| | Enable this component's loop.
|
| |
| void | enable_loop_soon_any_context () |
| | Thread and ISR-safe version of enable_loop() that can be called from any context.
|
| |
| bool | is_failed () const |
| |
| bool | is_ready () const |
| |
| virtual bool | can_proceed () |
| |
| bool | status_has_warning () const |
| |
| bool | status_has_error () const |
| |
| void | status_set_warning () |
| |
| void | status_set_warning (const char *message) |
| |
| void | status_set_warning (const LogString *message) |
| |
| void | status_set_error () |
| |
| void | status_set_error (const LogString *message) |
| |
| void | status_clear_warning () |
| |
| void | status_clear_error () |
| |
| | ESPDEPRECATED ("Use status_momentary_warning() without a name. Removed in 2027.5.0", "2026.11.0") void status_momentary_warning(const char *name |
| |
| void | status_momentary_warning (uint32_t length=5000) |
| | Set warning status flag and clear it after length ms.
|
| |
| void | status_momentary_warning (const LogString *message, uint32_t length=5000) |
| |
| | ESPDEPRECATED ("Use status_momentary_error() without a name. Removed in 2027.5.0", "2026.11.0") void status_momentary_error(const char *name |
| |
| void | status_momentary_error (uint32_t length=5000) |
| | Set error status flag and clear it after length ms.
|
| |
| void | status_momentary_error (const LogString *message, uint32_t length=5000) |
| |
| bool | has_overridden_loop () const |
| |
| const LogString * | get_component_log_str () const ESPHOME_ALWAYS_INLINE |
| | Get the integration where this component was declared as a LogString for logging.
|
| |
| bool | should_warn_of_blocking (uint32_t blocking_time, uint32_t &threshold_ms_out) |
| |
| WaterHeaterMode | get_mode () const |
| |
| float | get_current_temperature () const |
| |
| float | get_target_temperature () const |
| |
| float | get_target_temperature_low () const |
| |
| float | get_target_temperature_high () const |
| |
| uint32_t | get_state () const |
| | Get the current state flags bitmask.
|
| |
| bool | is_away () const |
| | Check if away mode is currently active.
|
| |
| bool | is_on () const |
| | Check if the water heater is on.
|
| |
| void | set_current_temperature (float current_temperature) |
| |
| virtual void | publish_state () |
| |
| virtual WaterHeaterTraits | get_traits () |
| |
| void | set_visual_min_temperature_override (float min_temperature_override) |
| |
| void | set_visual_max_temperature_override (float max_temperature_override) |
| |
| void | set_visual_target_temperature_step_override (float visual_target_temperature_step_override) |
| |
| const StringRef & | get_name () const |
| |
| bool | has_own_name () const |
| |
| uint32_t | get_object_id_hash () const |
| |
| StringRef | get_object_id_to (std::span< char, OBJECT_ID_MAX_LEN > buf) const |
| | Get object_id with zero heap allocation For static case: returns StringRef to internal storage (buffer unused) For dynamic case: formats into buffer and returns StringRef to buffer.
|
| |
| size_t | write_object_id_to (char *buf, size_t buf_size) const |
| | Write object_id directly to buffer, returns length written (excluding null) Useful for building compound strings without intermediate buffer.
|
| |
| bool | is_internal () const |
| |
| void | set_internal (bool internal) |
| |
| bool | is_disabled_by_default () const |
| |
| EntityCategory | get_entity_category () const |
| |
| const char * | get_device_class_to (std::span< char, MAX_DEVICE_CLASS_LENGTH > buffer) const |
| |
| StringRef | get_unit_of_measurement_ref () const |
| |
| const char * | get_icon_to (std::span< char, MAX_ICON_LENGTH > buffer) const |
| |
| uint32_t | get_device_id () const |
| |
| Device * | get_device () const |
| |
| bool | has_state () const |
| |
| void | set_has_state (bool state) |
| |
| | ESPDEPRECATED ("Use make_entity_preference<T>() instead, or preferences won't be migrated. " "See https://github.com/esphome/backlog/issues/85. Will be removed in 2027.1.0.", "2026.7.0") uint32_t get_preference_hash() |
| | Get a unique hash for storing preferences/settings for this entity.
|
| |
| template<typename T > |
| ESPPreferenceObject | make_entity_preference (uint32_t version=0) |
| | Create a preference object for storing this entity's state/settings.
|
| |
| | UARTDevice ()=default |
| |
| | UARTDevice (UARTComponent *parent) |
| |
| void | set_uart_parent (UARTComponent *parent) |
| |
| void | write_byte (uint8_t data) |
| |
| void | set_rx_full_threshold (size_t rx_full_threshold) |
| |
| void | set_rx_full_threshold_ms (size_t time) |
| |
| size_t | get_rx_full_threshold () |
| |
| void | set_rx_timeout (size_t rx_timeout) |
| |
| size_t | get_rx_timeout () |
| |
| void | write_array (const uint8_t *data, size_t len) |
| |
| void | write_array_progmem (const uint8_t *data, size_t len) |
| |
| void | write_array (const std::vector< uint8_t > &data) |
| |
| template<size_t N> |
| void | write_array (const std::array< uint8_t, N > &data) |
| |
| void | write_str (const char *str) |
| |
| bool | read_byte (uint8_t *data) |
| |
| bool | peek_byte (uint8_t *data) |
| |
| bool | read_array (uint8_t *data, size_t len) |
| |
| template<size_t N> |
| optional< std::array< uint8_t, N > > | read_array () |
| |
| size_t | available () |
| |
| UARTFlushResult | flush () |
| |
| int | read () |
| |
| size_t | write (uint8_t data) |
| |
| int | peek () |
| |
| | ESPDEPRECATED ("Use uart.final_validate_device_schema() in Python instead. Removed in 2027.3.0", "2026.9.0") void check_uart_settings(uint32_t baud_rate |
| | Check that the configuration of the UART bus matches the provided values and otherwise print a warning.
|
| |
|
| void | control (const water_heater::WaterHeaterCall &call) override |
| |
| water_heater::WaterHeaterTraits | traits () override |
| |
| void | check_timeouts_ (uint32_t now) |
| |
| void | send_pending_ (uint32_t now) |
| |
| void | read_frames_ (uint32_t now) |
| |
| void | poll_status_ () |
| |
| void | update_network_status_ () |
| |
| void | send_frame_ (water_heater_protocol::FrameType type, const uint8_t *payload=nullptr, size_t size=0) |
| |
| void | send_request_ (uint32_t now, Awaiting kind, water_heater_protocol::FrameType type, const uint8_t *payload, size_t size, water_heater_protocol::FrameType expected) |
| |
| void | send_next_control_ (uint32_t now) |
| |
| void | process_frame_ () |
| |
| void | handle_frame_type_ (water_heater_protocol::FrameType type) |
| |
| void | confirm_control_ (const water_heater_protocol::Status &status) |
| |
| void | publish_status_ (const water_heater_protocol::Status &status) |
| |
| friend | void::setup () |
| |
| friend | void::original_setup () |
| |
| void | set_component_source_ (uint8_t index) |
| | Set where this component was loaded from for some debug messages.
|
| |
| virtual void | call_setup () |
| |
| void | call_dump_config_ () |
| |
| void | enable_loop_slow_path_ () |
| |
| void | set_component_state_ (uint8_t state) |
| | Helper to set component state (clears state bits and sets new state)
|
| |
| bool | set_status_flag_ (uint8_t flag) |
| | Helper to set a status LED flag on both this component and the app.
|
| |
| bool | set_error_flag_ (const LogString *message) |
| | Set the error flag and log it; true when it was not set before.
|
| |
| void | set_interval (const char *name, uint32_t interval, std::function< void()> &&f) |
| | Set an interval function with a const char* name.
|
| |
| void | set_interval (uint32_t id, uint32_t interval, std::function< void()> &&f) |
| | Set an interval function with a numeric ID (zero heap allocation).
|
| |
| void | set_interval (InternalSchedulerID id, uint32_t interval, std::function< void()> &&f) |
| |
| void | set_interval (uint32_t interval, std::function< void()> &&f) |
| |
| bool | cancel_interval (const char *name) |
| | Cancel an interval function.
|
| |
| bool | cancel_interval (uint32_t id) |
| |
| bool | cancel_interval (InternalSchedulerID id) |
| |
| void | set_timeout (const char *name, uint32_t timeout, std::function< void()> &&f) |
| | Set a timeout function with a const char* name.
|
| |
| void | set_timeout (uint32_t id, uint32_t timeout, std::function< void()> &&f) |
| | Set a timeout function with a numeric ID (zero heap allocation).
|
| |
| void | set_timeout (InternalSchedulerID id, uint32_t timeout, std::function< void()> &&f) |
| |
| void | set_timeout (uint32_t timeout, std::function< void()> &&f) |
| |
| bool | cancel_timeout (const char *name) |
| | Cancel a timeout function.
|
| |
| bool | cancel_timeout (uint32_t id) |
| |
| bool | cancel_timeout (InternalSchedulerID id) |
| |
| void | defer (const char *name, std::function< void()> &&f) |
| | Defer a callback to the next loop() call with a const char* name.
|
| |
| void | defer (std::function< void()> &&f) |
| | Defer a callback to the next loop() call.
|
| |
| void | defer (uint32_t id, std::function< void()> &&f) |
| | Defer a callback with a numeric ID (zero heap allocation)
|
| |
| bool | cancel_defer (const char *name) |
| | Cancel a defer callback using the specified name, name must not be empty.
|
| |
| bool | cancel_defer (uint32_t id) |
| |
| void | status_clear_warning_slow_path_ () |
| |
| void | status_clear_error_slow_path_ () |
| |
| void | dump_traits_ (const char *tag) |
| | Log the traits of this water heater for dump_config().
|
| |
| optional< WaterHeaterCall > | restore_state_ () |
| | Restore the state of the water heater, call this from your setup() method.
|
| |
| void | set_mode_ (WaterHeaterMode mode) |
| | Set the mode of the water heater. Should only be called from control().
|
| |
| void | set_target_temperature_ (float target_temperature) |
| | Set the target temperature of the water heater. Should only be called from control().
|
| |
| void | set_target_temperature_low_ (float target_temperature_low) |
| | Set the low target temperature (for two-point control). Should only be called from control().
|
| |
| void | set_target_temperature_high_ (float target_temperature_high) |
| | Set the high target temperature (for two-point control). Should only be called from control().
|
| |
| void | set_state_ (uint32_t state) |
| | Set the state flags. Should only be called from control().
|
| |
| void | set_state_flag_ (uint32_t flag, bool value) |
| | Set or clear a state flag. Should only be called from control().
|
| |
| friend | void::setup () |
| |
| friend | void::original_setup () |
| |
| void | configure_entity_ (const char *name, uint32_t object_id_hash, uint32_t entity_fields) |
| | Combined entity setup from codegen: set name, object_id hash, entity string indices, and flags.
|
| |
| void | set_device_ (Device *device) |
| |
| ESPPreferenceObject | make_entity_preference_ (size_t size, uint32_t version) |
| | Non-template helper for make_entity_preference() to avoid code bloat.
|
| |
| void | calc_object_id_ () |
| |
Definition at line 13 of file hon_water_heater.h.
Public Member Functions inherited from esphome::Component
1.12.0