|
| | FUSB302B (InternalGPIOPin *interrupt_pin) |
| |
| void | setup () override |
| |
| void | loop () override |
| |
| void | dump_config () override |
| |
| void | on_shutdown () override |
| |
| float | get_setup_priority () const override |
| |
| void | request_voltage (int voltage) |
| | Negotiate a new contract with the highest source voltage that does not exceed voltage.
|
| |
| template<typename F > |
| void | add_on_state_callback (F &&callback) |
| | Callbacks receive each new state in order, with the state before it.
|
| |
| template<typename F > |
| void | add_on_request_failed_callback (F &&callback) |
| | Called when a voltage request was rejected, got no answer, or was dropped because the component failed.
|
| |
| void | set_voltage_sensor (sensor::Sensor *sensor) |
| |
| void | set_current_sensor (sensor::Sensor *sensor) |
| |
| void | set_contract_text_sensor (text_sensor::TextSensor *sensor) |
| |
| void | set_request_voltage (uint8_t voltage) |
| |
| uint8_t | get_request_voltage () const |
| |
| PdState | get_state () const |
| |
| bool | is_connected () const |
| |
| float | get_actual_setup_priority () const |
| |
| void | set_setup_priority (float priority) |
| |
| void | call () |
| |
| virtual void | on_safe_shutdown () |
| |
| virtual bool | teardown () |
| | Called during teardown to allow component to gracefully finish operations.
|
| |
| virtual void | on_powerdown () |
| | Called after teardown is complete to power down hardware.
|
| |
| uint8_t | get_component_state () const |
| |
| void | reset_to_construction_state () |
| | Reset this component back to the construction state to allow setup to run again.
|
| |
| bool | is_in_loop_state () const |
| | Check if this component has completed setup and is in the loop state.
|
| |
| bool | is_idle () const |
| | Check if this component is idle.
|
| |
| void | mark_failed () |
| | Mark this component as failed.
|
| |
| void | mark_failed (const LogString *message) |
| |
| void | disable_loop () |
| | Disable this component's loop.
|
| |
| void | enable_loop () |
| | Enable this component's loop.
|
| |
| void | enable_loop_soon_any_context () |
| | Thread and ISR-safe version of enable_loop() that can be called from any context.
|
| |
| bool | is_failed () const |
| |
| bool | is_ready () const |
| |
| virtual bool | can_proceed () |
| |
| bool | status_has_warning () const |
| |
| bool | status_has_error () const |
| |
| void | status_set_warning () |
| |
| void | status_set_warning (const char *message) |
| |
| void | status_set_warning (const LogString *message) |
| |
| void | status_set_error () |
| |
| void | status_set_error (const LogString *message) |
| |
| void | status_clear_warning () |
| |
| void | status_clear_error () |
| |
| | ESPDEPRECATED ("Use status_momentary_warning() without a name. Removed in 2027.5.0", "2026.11.0") void status_momentary_warning(const char *name |
| |
| void | status_momentary_warning (uint32_t length=5000) |
| | Set warning status flag and clear it after length ms.
|
| |
| void | status_momentary_warning (const LogString *message, uint32_t length=5000) |
| |
| | ESPDEPRECATED ("Use status_momentary_error() without a name. Removed in 2027.5.0", "2026.11.0") void status_momentary_error(const char *name |
| |
| void | status_momentary_error (uint32_t length=5000) |
| | Set error status flag and clear it after length ms.
|
| |
| void | status_momentary_error (const LogString *message, uint32_t length=5000) |
| |
| bool | has_overridden_loop () const |
| |
| const LogString * | get_component_log_str () const ESPHOME_ALWAYS_INLINE |
| | Get the integration where this component was declared as a LogString for logging.
|
| |
| bool | should_warn_of_blocking (uint32_t blocking_time, uint32_t &threshold_ms_out) |
| |
| | I2CDevice ()=default |
| | we use the C++ default constructor
|
| |
| void | set_i2c_address (uint8_t address) |
| | We store the address of the device on the bus.
|
| |
| uint8_t | get_i2c_address () const |
| | Returns the I2C address of the object.
|
| |
| void | set_i2c_bus (I2CBus *bus) |
| | we store the pointer to the I2CBus to use
|
| |
| I2CRegister | reg (uint8_t a_register) |
| | calls the I2CRegister constructor
|
| |
| I2CRegister16 | reg16 (uint16_t a_register) |
| | calls the I2CRegister16 constructor
|
| |
| ErrorCode | read (uint8_t *data, size_t len) const |
| | reads an array of bytes from the device using an I2CBus
|
| |
| ErrorCode | read_register (uint8_t a_register, uint8_t *data, size_t len) |
| | reads an array of bytes from a specific register in the I²C device
|
| |
| ErrorCode | read_register16 (uint16_t a_register, uint8_t *data, size_t len) |
| | reads an array of bytes from a specific register in the I²C device
|
| |
| ErrorCode | write (const uint8_t *data, size_t len) const |
| | writes an array of bytes to a device using an I2CBus
|
| |
| ErrorCode | write_read (const uint8_t *write_data, size_t write_len, uint8_t *read_data, size_t read_len) const |
| | writes an array of bytes to a device, then reads an array, as a single transaction
|
| |
| ErrorCode | write_register (uint8_t a_register, const uint8_t *data, size_t len) const |
| | writes an array of bytes to a specific register in the I²C device
|
| |
| ErrorCode | write_register16 (uint16_t a_register, const uint8_t *data, size_t len) const |
| | write an array of bytes to a specific register in the I²C device
|
| |
| bool | read_bytes (uint8_t a_register, uint8_t *data, uint8_t len) |
| | Compat APIs All methods below have been added for compatibility reasons.
|
| |
| bool | read_bytes_raw (uint8_t *data, uint8_t len) const |
| |
| template<size_t N> |
| optional< std::array< uint8_t, N > > | read_bytes (uint8_t a_register) |
| |
| template<size_t N> |
| optional< std::array< uint8_t, N > > | read_bytes_raw () |
| |
| bool | read_bytes_16 (uint8_t a_register, uint16_t *data, uint8_t len) |
| |
| bool | read_byte (uint8_t a_register, uint8_t *data) |
| |
| optional< uint8_t > | read_byte (uint8_t a_register) |
| |
| bool | read_byte_16 (uint8_t a_register, uint16_t *data) |
| |
| bool | write_bytes (uint8_t a_register, const uint8_t *data, uint8_t len) const |
| |
| bool | write_bytes (uint8_t a_register, const std::vector< uint8_t > &data) const |
| |
| template<size_t N> |
| bool | write_bytes (uint8_t a_register, const std::array< uint8_t, N > &data) |
| |
| bool | write_bytes_16 (uint8_t a_register, const uint16_t *data, uint8_t len) const |
| |
| bool | write_byte (uint8_t a_register, uint8_t data) const |
| |
| bool | write_byte_16 (uint8_t a_register, uint16_t data) const |
| |
|
| bool | send_message (const PdMsg &msg) override |
| |
| void | on_state_changed () override |
| |
| void | on_soft_reset_received () override |
| |
| void | on_source_caps_received () override |
| |
| void | on_transition_timeout () override |
| |
| void | on_request_failed () override |
| |
| void | run_task_ () |
| |
| bool | init_chip_ () |
| |
| bool | reset_pd_ () |
| |
| bool | enable_auto_crc_ () |
| |
| void | handle_interrupt_ () |
| |
| bool | read_message_ (PdMsg &msg, bool &is_sop) |
| |
| void | try_attach_ () |
| |
| bool | measure_cc_ (uint8_t meas_switch, uint8_t &level) |
| |
| void | detach_ () |
| |
| void | handle_hard_reset_ () |
| |
| void | start_source_cap_wait_ (SourceCapStep step) |
| |
| void | start_negotiation_ () |
| |
| void | send_soft_reset_ () |
| |
| void | source_caps_failed_ () |
| |
| void | check_source_caps_ () |
| |
| void | enter_error_ () |
| |
| void | publish_contract_ (PackedContract contract) |
| |
| void | publish_state_ (PdState state) |
| |
| void | queue_event_ (uint8_t event) |
| |
| void | handle_message_ (const PdMsg &msg) |
| |
| void | handle_transmit_failed_ () |
| | Called by the PHY when the chip gave up on a message after its retries without receiving a GoodCRC.
|
| |
| void | reset_protocol_ () |
| |
| void | set_state_ (PdState state) |
| |
| void | set_contract_ (const PdContract &contract) |
| |
| void | clear_contract_ () |
| |
| void | set_state_and_contract_ (PdState state, const PdContract &contract) |
| | Stores both before calling on_state_changed() once, so the main loop never sees the new state with the old contract.
|
| |
| void | set_ams_ (bool active) |
| |
| bool | check_ams_ () |
| | Returns true while an atomic message sequence is in progress.
|
| |
| void | check_transition_timeout_ () |
| | Falls back to default power when the source accepted a request but did not report the new supply ready in time.
|
| |
| void | check_request_retry_ () |
| | Sends the last request again once tSinkRequest has passed after the source answered Wait.
|
| |
| PdMsg | make_control_msg_ (PdControlMsgType type) const |
| |
| PdMsg | make_data_msg_ (PdDataMsgType type, const uint32_t *objects, uint8_t len) const |
| |
| friend | void::setup () |
| |
| friend | void::original_setup () |
| |
| void | set_component_source_ (uint8_t index) |
| | Set where this component was loaded from for some debug messages.
|
| |
| virtual void | call_setup () |
| |
| void | call_dump_config_ () |
| |
| void | enable_loop_slow_path_ () |
| |
| void | set_component_state_ (uint8_t state) |
| | Helper to set component state (clears state bits and sets new state)
|
| |
| bool | set_status_flag_ (uint8_t flag) |
| | Helper to set a status LED flag on both this component and the app.
|
| |
| bool | set_error_flag_ (const LogString *message) |
| | Set the error flag and log it; true when it was not set before.
|
| |
| void | set_interval (const char *name, uint32_t interval, std::function< void()> &&f) |
| | Set an interval function with a const char* name.
|
| |
| void | set_interval (uint32_t id, uint32_t interval, std::function< void()> &&f) |
| | Set an interval function with a numeric ID (zero heap allocation).
|
| |
| void | set_interval (InternalSchedulerID id, uint32_t interval, std::function< void()> &&f) |
| |
| void | set_interval (uint32_t interval, std::function< void()> &&f) |
| |
| bool | cancel_interval (const char *name) |
| | Cancel an interval function.
|
| |
| bool | cancel_interval (uint32_t id) |
| |
| bool | cancel_interval (InternalSchedulerID id) |
| |
| void | set_timeout (const char *name, uint32_t timeout, std::function< void()> &&f) |
| | Set a timeout function with a const char* name.
|
| |
| void | set_timeout (uint32_t id, uint32_t timeout, std::function< void()> &&f) |
| | Set a timeout function with a numeric ID (zero heap allocation).
|
| |
| void | set_timeout (InternalSchedulerID id, uint32_t timeout, std::function< void()> &&f) |
| |
| void | set_timeout (uint32_t timeout, std::function< void()> &&f) |
| |
| bool | cancel_timeout (const char *name) |
| | Cancel a timeout function.
|
| |
| bool | cancel_timeout (uint32_t id) |
| |
| bool | cancel_timeout (InternalSchedulerID id) |
| |
| void | defer (const char *name, std::function< void()> &&f) |
| | Defer a callback to the next loop() call with a const char* name.
|
| |
| void | defer (std::function< void()> &&f) |
| | Defer a callback to the next loop() call.
|
| |
| void | defer (uint32_t id, std::function< void()> &&f) |
| | Defer a callback with a numeric ID (zero heap allocation)
|
| |
| bool | cancel_defer (const char *name) |
| | Cancel a defer callback using the specified name, name must not be empty.
|
| |
| bool | cancel_defer (uint32_t id) |
| |
| void | status_clear_warning_slow_path_ () |
| |
| void | status_clear_error_slow_path_ () |
| |
FUSB302B USB Type-C / Power Delivery sink controller.
A dedicated task owns all I2C traffic to the chip so that PD replies meet the protocol timing even while the main loop is busy. The main loop only publishes state changes.
Definition at line 30 of file fusb302b.h.